Order Request Form

Please answer the following questions and submit your stair tread request to us.
Contact Information
Q1: Tell Us About This Address
Q2: Select the tread type you are inquiring about
Please note: Standard Treads and Custom Thick Treads are designed to be installed onto your stair frames stringers while Full False Treads are designed to fit over existing treads or roughed in treads such as one would find when removing carpet from stairs.
Q3: How many treads in total and what wood species do you require?
Q4: What size treads do you require? If multiple sizes or custom thick treads select that option and enter details below
Enter your details on multiple sizes (i.e.; 12 Treads x 36 in. - 4 Treads x 42 in. ):
**Include Length/Thickness/Widths for Custom Tread Request ( i.e; 12 Treads - 36 x 12 x 4 ):
Q5: If selecting ( Full False / Full False Modern ) treads we require the following measurements.
The existing "riser to riser" width or the ( Run ) as it is referred to, this is then transferred to the ( Plowed ) out area on your full false treads ( please see reference photos below). Do not include any overhang or bull nose widths in your ( Run ) measurement. We recommend measuring a number of your existing treads to ensure tread measurements have consistency throughout.

Our treads have a standard 9" plowed area, though these can easily be cut to size on site for smaller plow requirements or we can can make them wider depending on our customers requirements. Once you exceed a 9-1/2" plowed area you are looking at additional costs per tread.

Note: To install full false treads it is required that you cut back the existing bull nose ( front edge overhang ) so that the existing treads are square or flush with the existing risers.

Q6: Are your treads all enclosed between walls or skirt board or are there some open ended stair treads?
( Note: Not applicable for Custom Thick Treads )
Q7: Do you require new risers or the recommended stair trim included with your quote?
Will you be wanting new risers or the recommended stair trim included with your quote? Ogee Cove Moulding is a finishing trim used to go under the treads front side where the riser meets the bottom of the stair treads underside, to hide the little 1/8 in. and 1/16 in. gaps that may be there after the install. We definitely suggest getting the trim especially if we are doing the finish to ensure match consistency.

Typically you require ( 1 ) more riser than you do stair treads per straight run of stairs. For example if you have a continuous run of ( 12 ) treads youll require ( 13 ) risers, if the stairs are split ( with a landing area etc.; ) then youd need ( 14 ) or more risers. Our risers are sold in 4 ft. or 8 ft. lengths only with the 4 ft. option being the least expensive to ship.

If required, can you let us know the number of risers you require?
Q8: Can you confirm if " Natural " or " Clear " is the grain face profile you prefer.
Oak is shown in the sample and shows the typical face grain differences. On standard treads there is an up cost of $5.00 per tread for the "Clear" profile. There is no up cost for the clear profile on our full false treads, simply customer preference.
Q9: Do you require a finish?
MinWax Stains: The available Minwax stains can be viewed below or we can custom stain match to a physical piece of flooring. Please note, we would need an actual piece of the existing flooring to be color matched sent to us as we can not stain match to a photo.
If stain finish is required, choose one of the following two options:
In the stair business a “quick quote” is not always possible due to all the variables that must be accounted for. It is possible, dependent on your answers, that we may still require some additional information to ensure you receive and are properly quoted on the correct sized materials for your staircase project.

We look forward to hearing from you and serving your needs!

Proudly Made in Canada